M.2 Nvme Ssd Adapter For Raspberry Pi 5
I 10 migliori prodotti di ottobre 2025
Ultimo aggiornamento:
6 ottobre 2025
Geekworm
Geekworm X1001 PCIe to M.2 NVMe SSD Shield per Raspberry Pi 5
Spedizione gratuita
99
QUALITÀ MASSIMA
VEDI SU AMAZON
Amazon.it
#1 VINCITORE
▼ Mostra di più
▲ Mostra di meno
【Compatibility】only for Raspberry Pi 5 16GB / 8GB / 4GB (NOT included)
【Matching Case (NOT included)】P579 Case (ASIN: B0CRB3DT5M); Or P579 Case with Official Active Cooler (ASIN: B0CT4P893Q)
【M2 Key-M NVMe SSD Supported】Support M.2 KEY-M NVMe SSD 2230/2242/2260/2280 length installation.【IMPORTANT】DON'T use NVMe SSD with Phison controller, please refer to: https://wiki.geekworm.com/X1001#Important_Notes
【How to Power】Use 5Vdc +/-5%, 5A to power via Raspberry Pi 5, and Pi 5 will power X1001 via FFC PCIe ribbon. Recommend to use Geekworm PD 27W power adapter (ASIN: B0CP8SRXSC / B0CZCZF2QV)
【Packing List】1 x X1001 Shield, 1x Accessories Pack
16,40 € SU AMAZON
Freenove
Freenove M.2 NVMe Adapter for Raspberry Pi 5 (with 128GB SSD), M.2 HAT Add-on Board, Solid State Drive, PCIe 2.0/3.0, Tested Speed 800 MB/s
Spedizione gratuita
96
QUALITÀ SUPERIORE
VEDI SU AMAZON
Amazon.it
#2
▼ Mostra di più
▲ Mostra di meno
Big Upgrade: Boost your system to an amazing speed by upgrading memory card (usually read: 100 MB/s, write: 10 MB/s) to SSD (PCIe 2.0: read: 419 MB/s, write: 253 MB/s; PCIe 3.0: read: 804 MB/s, write: 404 MB/s. Tested with this SSD on Raspberry Pi 5)
Comes with 128GB SSD: M.2 interface, NVMe protocol, PCIe 2.0 or 3.0, size 2280 (The write speed of SSD is much faster than that of memory card)
Two Uses: Used as system disk or regular hard drive, provide detailed tutorial (The download link can be found on the product box) (No paper tutorial)
Easy to Use: Just tighten the screws and connect the ribbon cable to install it on the bottom (Simple configuration needed, please refer to tutorial)
Compatible Models: Raspberry Pi 5 only (Note: NOT compatible with any other models)
25,95 € SU AMAZON
GeeekPi
GeeekPi N07 M.2 PCIe to NVMe Bottom SSD Pip PCIe Peripheral Board for Raspberry Pi 5,Support M.2 Key-M NVMe SSD 2230/2242/2260/2280 (SSD and Pi5 Board are Not Included)
Spedizione gratuita
92
QUALITÀ OTTIMA
VEDI SU AMAZON
Amazon.it
#3
▼ Mostra di più
▲ Mostra di meno
【Compatibility】GeeekPi N07 PCIe M.2 M-key NVMe SSD Pip Peripheral Board Bottom is only compatible with Raspberry Pi 5 8GB 4GB board. Nota: Raspberry Pi 5 board is not included.
【Supporto M.2 NVMe SSD】Raspberry Pi 5 N07 M.2 NVMe SSD Adapter Board is a bottom-mounted adapter and it supports the installation of M.2 M-key NVMe SSD 2230/2242/2260/2280.
【How to Power】Use 5 Vdc +/-5%, 5 A to power via Raspberry Pi 5 and Pi 5 will power N07 tramite pin pogo per extra power during large data transfer. and the data will transfer via FFC ribben cable with Raspberry Pi 5 via PCIe slot, consiglia di utilizzare GeeekPi PD 27W power adapter (ASIN: B0CQ1Q18HX)
【Cooling Solution】Ventilazione hole design fornisce un'eccellente ventilazione dell'aria per il raffreddamento e supporto per Raspberry Pi 5 Active Cooler installazione.
Pacchetto incluso: 1 x N07 M.2 2280 PCIe to NVMe Bottom; 1 x cavo personalizzato PCIe FFC, 4 x M2,5 x 6 mm Copper pillar; 4 x M2,5 x 12+4 mm lungo Copper pillar; 4 x M2,5 x 4 mm Flat head screw; 2 x M2 x M2 x M2 mm Hard drive copper piller. ars and Screws (to fix NVME M.2 SSD)
【Wiki】https://wiki.52pi.com/index.php?title=EP-0211
18,99 € SU AMAZON
Waveshare
PCIe To M.2 Adapter Board (E) with Cooling Fan For Raspberry Pi 5,Compatible With 2242/2230 Size NVMe Protocol M.2 SSD,for Raspberry Pi 5 NVMe HAT
Spedizione gratuita
92
QUALITÀ OTTIMA
VEDI SU AMAZON
Amazon.it
#4
▼ Mostra di più
▲ Mostra di meno
PCIe TO M.2 Board (E) Suitable for Raspberry Pi 5,Compact Size, Cooling Fan All-in-One Design
Adapter For NVMe Protocol M.2 Solid State Drive, Improves Working Efficiency
Improves Reading/Writing Speed Of Your Pi
Matching The Size And Mounting Holes Of The Raspberry Pi 5,Combines A Temperature-Controlled Blower Fan With An Aluminium Heatsink To Accelerate Heat Dissipation
Connecting To PI5 Via 16PIN Cable,Based On 16PIN PCIe Interface Of Raspberry Pi 5
19,99 € SU AMAZON
Waveshare
PCIe To M.2 Mini Adapter Board Compatible with Raspberry Pi 5,Supports NVMe Protocol 2230/2242 Size M.2 Solid State Drive,for Raspberry Pi 5 NVMe HAT
Spedizione gratuita
83
QUALITÀ AFFIDABILE
VEDI SU AMAZON
Amazon.it
#5
▼ Mostra di più
▲ Mostra di meno
PCIe To M.2 Mini Adapter only Compatible with Raspberry Pi 5
Support NVMe protocol and M.2 solid state drive protocol, high-speed read/write, with high work efficiency.
Support PCI-E×1 Gen2 or Gen3 modes.
Compatible with M.2 solid state drive of 2230/2242 sizes.
Onboard working indicator lights, with PWR on continuously when powered, and ACT blinking during read/write.
12,49 € SU AMAZON
Freenove
Freenove Dual M.2 NVMe SSD HAT for Raspberry Pi 5, M.2 Adapter AI HAT 2 Slots NAS RAID Kit, Solid State Drive Size 2230 2242 2260 2280, PCIe 2.0 Max Speed 500 MB/s, Detailed Tutorial
Spedizione gratuita
82
QUALITÀ AFFIDABILE
VEDI SU AMAZON
Amazon.it
#6
▼ Mostra di più
▲ Mostra di meno
Big Upgrade: Boost your system to an amazing speed by upgrading memory card (SDR104: 104 MB/s max) to SSD (PCIe 2.0: 500 MB/s max) (The write speed of SSD is much faster than that of memory card) (Note: The max speed is declared by the Raspberry Pi documentation, usually unable to achieve)
Dual M.2 Slots: Install 1 or 2 SSDs, used as system disk, regular hard drive or bulid a NAS / RAID. Provide detailed tutorial for Raspberry Pi OS (The tutorial link can be found on the product box, no paper tutorial)
AI Accelerator: Compatible with M.2 Hailo AI accelerator module, so you can integrate high-performance AI (AI module can operate both when installed alone and together with an SSD on dual-slot adapter)
Easy to Use: Just tighten the screws and connect the ribbon cable to install it on the top or bottom (Some SSDs may require connecting the power cable)
Compatible SSDs: M.2 NVMe SSDs, compatible with PCIe 2.0, size 2230 / 2242 / 2260 / 2280 (Note: NOT compatible with M.2 SATA SSDs) (This adapter can be shortened to be shorter than Raspberry Pi, but will not be able to install 2280 size)
19,95 € SU AMAZON
ZDE
ZDE ZP518 PCIe to Dual M.2 HAT Key M NVMe SSD PCIe Peripheral Board Solid State Drive Adapter Board for Raspberry Pi 5 Support M.2 NVMe SSD 2230 2242
Spedizione gratuita
79
QUALITÀ BUONA
VEDI SU AMAZON
Amazon.it
#7
▼ Mostra di più
▲ Mostra di meno
Dual M.2 NVMe SSDs Supported: ZP518 PCIe to Dual M.2 HAT Key-M NVMe SSD expansion board supports the installation of two M.2 Key-M NVMe SSDs in 2230/2242 length, high-speed reading/writing; supports booting pi5 from nvme solid state drive.
Compatibility: This PCIe to Dual M.2 HAT NVMe kit is only compatible with Raspberry Pi 5 2GB/4GB/8GB/16GB SBC.
How to Power: Power the adapter directly from the PCIe FPC ribbon cable. Also, with 40pin GPIO header, the board can automatically supply power from GPIO, avoiding the problem of insufficient power supply for ultra-large capacity of SSDs.
Cooling Solution: Supports the installation of official Pi 5 Active Cooler (Not Included) and there is a reserved airflow vent for the cooling fan, better heat dissipation effect for Raspberry Pi 5 and SSD.
Practical Accessories: Comes with 2pcs M2 studs for 2230/2242 SSD installation, no soldering required. For aluminum case, please refer to ZC501(ASIN: B0DSZYLMSS).
25,99 € SU AMAZON
GeeekPi
GeeekPi Metal Case for Raspberry Pi 5,with N04 M.2 NVMe SSD PCIe Peripheral Board,Official Active Cooler and 27W USB C Power Adapter for Raspberry Pi 5 8GB 4GB
Spedizione gratuita
76
QUALITÀ BUONA
VEDI SU AMAZON
Amazon.it
#8
▼ Mostra di più
▲ Mostra di meno
【Compatibility】This kit includes a metal case, a N04 M.2 Key-M NVMe SSD PCIe Peripheral Board,and an official active cooler and a PD 27W Power Adapter; It is compatible with the latest Raspberry Pi 5 4GB/8GB and Supports M.2 NVMe SSD 2230 2242 2260 2280.
【Access to all Ports】GeeekPi Raspberry Pi 5 Case can accurately access most ports of Raspberry Pi board, including usb-c power jack, micro HDMI ports, usb ports, Ethernet jack, sd card slot, power button, and GPIO Slot.
【N04 M.2 NVMe to PCIe Adapter Included】N04 M.2 NVMe to PCIe Adapter is designed for the latest Raspberry Pi 5. It supports the installation of NVMe (M-key) drives in M.2 format sizes 2230, 2242, 2260 and 2280. Extra custom CNC SSD mount screw, no soldering required.
【Raspberry Pi 5 Active Cooler Included】Raspberry Pi 5 Active Cooler combines an aluminium heatsink with a PWM fan to keep your Raspberry Pi 5 maintain optimal operating temperatures, ensuring reliable performance for various applications.
【Raspberry Pi 5 Power Supply Included】5.1V 5A 27W USB C power Supply is designed for Raspberry Pi 5 board. The power adapter is equipped with Power Delivery technology, allowing for fast and efficient charging of compatible devices. It also offers a variety of output voltage options, including 5.1V at 5A, 9.0V at 3.0A, 12.0V at 2.25A, and 15.0V at 1.8A, providing flexibility for different device requirements.
49,99 € SU AMAZON
ZDE
ZDE ZP593 PCIe to 2.5G Ethernet Network Port PCIe to M.2 Key M NVMe SSD HAT Adapter Expansion Board for Raspberry Pi 5 Support M.2 NVMe 2230 2242 2260 2280 SSD
Spedizione gratuita
72
QUALITÀ BUONA
VEDI SU AMAZON
Amazon.it
#9
▼ Mostra di più
▲ Mostra di meno
This expansion board adds one 2.5GBE network port and one M.2 Key-M interface for Raspberry Pi 5, which can meet your various needs for those who need to use Raspberry Pi 5 as a Router, Gateway, Firewall, Robot, Smart Home, NAS, VOIP, Industrial Equipment, Telecommunications Equipment and other network devices that need more than one network port.
Through the PCIe interface with PCIe Switch chip to expand into two PCIe interfaces and then through the RTL8125 chip to achieve the expansion of 2.5Gbps Ethernet and M.2 Key-M NVME.
After power on, the board can be automatically recognised as eth1 without installing driver under Raspberry Pi official OS system. When you use OpenWrt, you need to compile the RTL8125 driver into the firmware. When you use ubuntu system, you need to install the driver of RTL8125 and then you can use it.
Support M.2 NVMe SSD for expansion and storage, compatible with M.2 KEY-M NVMe SSD in 2230/2242/2260/2280 length. Support boot from SSD, and it needs Raspberry Pi official firmware, which is at least 2024.5.13.
With four M2.5 fixing holes, the concave design on the top of the board is convenient for the operation and use of 40Pin GPIO.
26,99 € SU AMAZON
Miuzei
Miuzei Custodia in metallo per Raspberry Pi 5, 1 viti, compatibile con adattatore M.2 NVMe SSD X1001/X1003/N04/N05 e Active Cooler, per Raspberry Pi 5 Only
Spedizione gratuita
68
QUALITÀ BUONA
VEDI SU AMAZON
Amazon.it
#10
▼ Mostra di più
▲ Mostra di meno
Compatibile con piastre adattatore SSD M.2 NVMe leader del mercato tra cui X1001/X1003/N04/N05, supporta tutti i formati da 2280 a 2230,10 mm, spazio verticale SSD-PCB e coperchio ideale per dissipatore di calore e pad termico, compatibile con Raspberry Pi 5 in 2GB/4GB/8GB/16 GB
Raffreddatore originale Raspberry Pi 5 con pieno produttore di terze parti. Compatibilità: Plug and Play per refrigeratori attivi ufficiali (senza moduli aggiuntivi), lunghezza del cavo FPC ottimizzata a 50-70 mm (oltre 70 mm rischio di blocco della ventola). Le viti distanziatrici da 4 x 16 mm consentono una distanza tra le ventole SSD di 4 mm (+83% di potenza di raffreddamento rispetto a Design standard). Supporta soluzioni di raffreddamento Miuzei come ASIN B0CTMFH133 (venduto separatamente).
Viti singole Quick Release e telaio ultra sottile da 3 mm: lo smontaggio può essere effettuato in soli 1 secondo, ideale per frequenti aggiornamenti hardware o esperimenti di laboratorio. Design del telaio ultra sottile che massimizza l'area di lavoro di 63 mm e garantisce il funzionamento senza ostacoli.
Integrazione dell'interfaccia a filo: perfetta vestibilità senza cavità – Le interferenze di contatto vengono efficacemente evitate grazie all'allineamento del connettore calibrato al laser (HDMI/USB-C/Ethernet), predisposto per pulsante di alimentazione e porta per schede SD per migliorare la facilità d'uso.
Accessori completi – Pronto per l'uso: incluso: 1 x alloggiamento in metallo; 1 x cacciavite; 4 x piedini in gomma fumante; 4 x supporti a vite (vedi istruzioni). Non incluso: dissipatore di calore; adattatore NVMe; M.2 SSD; Raspberry Pi 5 (venduto separatamente).
12,99 € SU AMAZON
raspberry pi 5 ssd m.2
ssd for raspberry pi 5
raspberry pi 5 ssd adapter
raspberry pi 5 ssd nvme
m.2 nvme ssd adapter
nvme m.2 ssd adapter
pironman 5 nvme m.2 ssd pcie mini pc case for raspberry pi 5
nvme adapter raspberry pi 5
nvme base for raspberry pi 5
geeekpi n04 m.2 m-key nvme ssd shield for raspberry pi
#1 VINCITORE
