Hc-sr501: 10 migliori di ottobre 2025

▼ Mostra di più▲ Mostra di meno

【Easy operation-1】1. Sensing module for about a minute after power initialization time, during the interval to the output module 0-3 times a minute in standby mode.2. Should avoid direct lighting such as interference sources close the surface of the lens module so as to avoid the introduction of interference signal generator malfunction; use of the environment to avoid the flow of the wind, the wind sensor will also cause interference.
【Easy operation-2】3. Sensor module using a dual probe, the probe's window is rectangular, dual (A per B million) in the direction of the ends of long, when the body passed from left to right or right to left when the reach the dual IR time, distance difference, the greater the difference, more sensitive sensors, when the body from the front to the probe or from top to bottom or from bottom to top direction passing, dual IR not detected changes in the distance;
【Easy operation-3】so the sensors should be installed dual direction of the probe with human activities as much as possible parallel to the direction of maximum to ensure that the body has been passed by the dual sensor probe. To increase the sensing range of angles, the module using a circular lens, the probe also makes sense on all four sides, by the above installation requirements.VCC, trig (control side), echo (receiving end), GND.
【Easy operation-4】5, with induction blocking time (the default setting: 2.5S block time): sensor module, after each sensor output (high change Into a low level),can set up a blockade followed by time period, in this time period the sensor does not accept any sensor signal. This feature can have a "sensor output time" and "blocking time" the interval between the work produced can be applied to detect the interval Products .
【Easy operation-5】6, the working voltage range: the default voltage DC4.5V-20V. 7, micro-power consumption: static current "50 microamps, especially for battery-powered automatic control products. !!Note!!: The potentiometer clockwise to adjust the distance, sensing range increases (about 7 meters), on the contrary, sensing range decreases (about 3 meters).Delay adjustment potentiometer clockwise rotation, sensor delay longer (about 300S), the other hand, induction by the short delay (about 5S).
12,64 € SU AMAZON

Hc-sr501

I 10 migliori prodotti di ottobre 2025

Ultimo aggiornamento: 9 ottobre 2025

AZDelivery

AZDelivery Sensori di movimento HC-SR501 PIR Modulo di rilevazione di movimento compatibile con Arduino incluso un E-Book!

98

QUALITÀ MASSIMA

Amazon.it

Jopto

Jopto 5PCS Sensori di Movimento SR501 PIR Modulo di Rilevazione di Movimento SR501 Corpo Umano Piroelettrici Sensore di Movimento PIR Sensore Infrarossi Moduli

97

QUALITÀ SUPERIORE

Amazon.it

ARCELI

Moduli per rivelatori di sensori di movimento PIR a infrarossi piroelettrici IR ARCELI

94

QUALITÀ OTTIMA

Amazon.it

Teklife

Teklife PIR SENSORE INFRAROSSO MOVIMENTO HC-SR501 PIC BIANCO

91

QUALITÀ DISTINTA

Amazon.it

Binghe

PIR Modulo Sensori di Movimento Binghe 3 pezzi PIR Sonda del sensore a infrarossi PIR Sensore Infrarosso IR Corpo Umano Modulo compatibile con Arduino

85

QUALITÀ AFFIDABILE

Amazon.it

TR Computers

3 moduli di hc-sr501 sensore di movimento PIR per Raspberry Pi o Arduino. Viene fornito con una carta per cablaggio GPIO Pi by TR computer

82

QUALITÀ AFFIDABILE

Amazon.it

TECNOULAB

TECNOULAB 2 pezzi SR501 HC-SR501 HCSR501 Regola il sensore di movimento IR

81

QUALITÀ BUONA

Amazon.it

TECNOIOT

5pcs SR501 HC-SR501 HCSR501 Adjust IR Motion Sensor

77

QUALITÀ BUONA

Amazon.it

PIRABADI

Modulo HC-SR501 SENSORE DI Movimento HC SR501 Compatibile con ARDUINO RASP... (672)

74

QUALITÀ BUONA

Amazon.it

BEMATIK.COM

BeMatik - Sensore rilevatore di movimento PIR piroelettrico a infrarossi HC-SR501 (AJ004)

69

QUALITÀ BUONA

Amazon.it